Finding your suitable arduino cnc shield v3 is not easy. You may need consider between hundred or thousand products from many store. In this article, we make a short list of the best arduino cnc shield v3 including detail information and customer reviews. Let’s find out which is your favorite one.
Best arduino cnc shield v3
1. kuman CNC Shield Expansion Board V3.0 +UNO R3 Board + A4988 Stepper Motor Driver With Heatsink for Arduino Kits K75 (CNC Shield+UNO R3+Stepper Motor)
Feature
LatestCNCShieldVersion3.0forArduinoArduino UNO R3 Board, MCU: ATmega328, USB interface: ATmega16U2
PWM Spindle and direction pins. 4-Axis support. Runs on 12-36V DC
2 x End stops for each axis (6 in total)
4pcs A4988 Stepper Motor Driver with radiator
Description
CNC Shield Board:Latest Arduino CNC Shield Version 3.0
GRBL 0.9 compatible
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis (6 in total)
Coolant enable
Compatible with A4988 or DRV8825 stepper driver
Runs on 12-36V DC
Arduino UNO R3 Board:
MCU: ATmega328
USB interface: ATmega16U2
Operating voltage: 5V
Digital I/O pins: 14 (including 6 with PWM capability)
Analog input pins: 6
I-I/O pin output current: 40mA max
3.3V output current: 150mA max
Flash memory: 32 kB (0.5kB used by bootloader - included)
Static RAM (SRAM): 2 kB
EEPROM: 1 kB
Clock speed: 16MHz
A4988 Stepper Motor Driver:
A4988 Stepper Motor Driver Board is a breakout board for Allegro's A4988 DMOS Micro stepping Driver with Translator and Overcurrent Protection;
Low RDS (On) Output
Automatic current decay mode detection / selection
Mix with slow current decay modes
Synchronous rectification for low power dissipation
Internal UVLO
Crossover-current protection
3.3 and 5 V compatible logic supply
Thermal shutdown circuitry
Ground fault protection
Load short-circuit protection
Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16
Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it is powered is asking for trouble).
PackageContents:
1xCNCShieldBoard
1xUNOR3BoardforArduino
4xA4988StepperMotorDriver
4xHeatSink
2. Quimat Arduino CNC Shield Contoller Kits for 3D Printer,CNC Shield V3.0 + UNO R3 Board + Nema 17 Stepper Motor + A4988 Stepper Motor Driver + Heat Sinks,Perfectly Compatible with GRBL
Feature
CNC Shield V3.0 Features - Latest Version 3.0, GRBL 0.8c compatible, 4 Axis supported and 2 end stops for each axis.Compact design - Stepper motors can be connected with 4 pin molex connectors or soldered in place.
Stepper Drivers - Uses removable Pololu A4988 compatible stepper drivers, jumpers to set the Micro-Stepping for the stepper drivers
Stepping Motor Included - Nema 17 model, holding torque of 26Ncm(36.8oz.in), 12V/0.4A and 1.8 deg.step angle(200 steps/rev)
Technical support - Our technical support team is on standby to provide solutions to your questions, please feel free to contact us.
Description
CNC Shield V3.0 features: Latest Arduino CNC Shield Version 3.0. GRBL 0.8c compatible.(Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) 4-Axis support(X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13) 2 x End stops for each axis(6 in total), Spindle enable and direction Coolant enable Stepper drivers Uses removable Pololu A4988 compatible stepper drivers. Jumpers to set the Micro-Stepping for the stepper drivers. Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.) Stepping Motor The most popular Nema 17 model with 1.8 deg. step angle (200 steps/revolution) 0.4A rated current/phase, allowing for a holding torque of 26Ncm(36.8oz.in) Connection:Black(A+), Green(A-), Red(B+), Blue(B-) Stepping Motor Specification: * Cable length: 11.8 inches * Phase Resistance: 30ohms * Inductance: 37mH+/-20%(1KHz) * Frame Size: 42 x 42mm * Body Length: 34mm * Shaft Diameter: 5mm * Front Shaft Length: 20mm * D-cut Length: 15mm * Number of Leads: 4 * Lead Length: 300mm * Weight: 230g Kit list: 1x CNC Shield V3.0 1x Keyestudio UNO R3 board 4x A4988 driver 1x USB cable 1x Nema 17 stepping motor3. 3D Printer CNC Controller Kit with for ArduinoIDE, Longruner GRBL CNC Shield Board+RAMPS 1.4 Mechanical Switch Endstop DRV8825 A4988 Stepper Motor Driver Nema 17 Stepper Motor LKB02
Feature
Latest CH340G CNC Shield expansion board Version 3.0 for Arduino.Longruner UNO R3 Board, MCU: ATmega328, USB interface: ATmega16U2 with 1.5m USB Cable.
4pcs DRV8825 Stepper Motor Driver with Heat Sinks.
3pcs NEMA-17 Stepper Motor 84 oz.in (59 Ncm) 47mm Body 1.8 degree with Mounting Bracket Kit DIY 3D Printer CNC Robot with 3pcs Mounting Bracket and 12pcs M3 Screws.
3pcs Endstop Mechanical Limit Switches for 3D printer RAMPS 1.4 with 3Pin 70cm Cable.
Description
CNC Shield Board: Latest CNC Shield Version 3.0 for arduino. GRBL 0.9 compatible. 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13). 2 x End stops for each axis (6 in total). Coolant enable. Compatible with A4988 or DRV8825 stepper driver. Runs on 12-36V DC. DRV8825 Stepper Motor Driver: Stepper motor driver (upgraded from A4988, 2.5 A max current/phase. It's not arduino official board but it's compatible with all arduino software and hardware). Nema 17 Stepper motor Specification: Model No.:17HD48002H-22B Step Angle: 1.8 deg Holding Torque: 59Ncm(84 oz.in) Rated Current/phase: 1.7A Frame Size: 41 x 41mm Body Length: 47mm Shaft Diameter: 5mm Shaft Length: 22mm Weight: 380g Mechanical Endstop Connection Description: Red line connect VCC (ramps of +) black wire connect the GND (ramps of -) Green Line connect SIGNAL (ramps in s) Tips: Under normal circumstances, the system must be configured to at least three mechanical switches. Advantage: Easy to install, the more common used styles. Length of Cable: 70 cm Great Package Includes: 1 x CNC Shield Board 1 x Longruner UNO R3 Board 1 x 1.5m USB cable for R3 Board 3 x Nema 17 stepper motor 1.7 A (with bracket and screw) 3 x Nema 17 Stepper Motor Mounting Bracket 3 x Mechanical Switch Endstop 3 x 3Pin 70cm Cable 4 x DRV8825 Stepper Motor Driver 4 x Aluminum heatsink w/ 3M tape backing 12x M3 Screws for bracket of stepper motorIf you have any question, please be free to contact us, we will try our best to help you. Service Email: [email protected]4. HiLetgo 2pcs A4988 V3 Engraver Drive Shield 3D Printer CNC Drive Expansion Board for Arduino 3D Printer CNC
Feature
Each road stepper motors only need two IO portsThis expansion board as a driver expansion board, can be used for engraving machines, 3D printers.
PWM Spindle and direction pins. 4-Axis support. Runs on 12-36V DC
It is a total of four slots, can drive four A4988 stepper motor. Each road stepper motors only need two IO ports. In other words, six IO ports can be well managed three stepper motors. Very convenient to use.
Stepper motor wiring as follows: 2A, 2B is a group (red, green), 1A, 1B is a group (blue, yellow), if want to change direction, can be change the position of one group , for example 2A, 2B mutually exchanged.
Description
GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)PWM Spindle and direction pins
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis (6 in total)
Coolant enable
Uses removable A4988 or DRV8825 compatible stepper drivers
Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping)
Compact design.
Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
Runs on 12-36V DC. (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
Please note that this is an unassembled kit and Basic soldering skills are needed
Package List:
1*V3 Engraver Shield 3D Printer CNC Expansion Board A4988 Driver Board
5. OctagonStar A4988 Driver CNC Shield Expansion Board for Arduino V3 Engraver 3D Printer
Feature
A4988 Driver CNC Shield Expansion Board.Each road stepper motors only need two IO ports.
Six IO ports can be well managed three stepper motors. Very convenient to use.
Description
This expansion board as a driver expansion board, can be used for engraving machines, 3D printers.It is a total of four slots, can drive four A4988 stepper motor.
Each road stepper motors only need two IO ports.
Package included:
1 X A4988 Driver CNC Shield Expansion Board.
6. Gowoops 3D Printer kit CNC Shield V3 Expansion Board + UNO R3 Board + 4PCS DRV8825 Step Motor Driver with Heatsinks for Arduino
Feature
Latest Arduino CNC Shield Version 3.0, CNC Capacitance: 50V 100uFPWM Spindle and direction pins. 4-Axis support. Runs on 12-36V DC
Arduino UNO R3 Board, MCU: ATmega328, USB interface: ATmega16U2
The DRV8825 features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/32-step).
The DRV8825 operates from 8.2 - 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to 2.2 A per coil with sufficient additional cooling
Description
Arduino CNC Shield V3.0 Installation Guide:http://osoyoo.com/?p=4783
CNC Shield Board: (learn more information, pls go to the ASIN: B0157ZZ28M)
Please note that this is an unassembled kit and Basic soldering skills are needed
Arduino UNO R3 Board:
MCU: ATmega328
USB interface: ATmega16U2
Operating voltage: 5V
Digital I/O pins: 14 (including 6 with PWM capability)
Analog input pins: 6
I-I/O pin output current: 40mA max
3.3V output current: 150mA max
Flash memory: 32 kB (0.5kB used by bootloader - included)
Static RAM (SRAM): 2 kB
EEPROM: 1 kB
Clock speed: 16MHz
DRV8825 Stepper Motor Driver Module:
Simple step and direction control interface
Can interface directly with 3.3 V and 5 V systems
Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout
Short-to-ground and shorted-load protection
4-layer, 2 oz copper PCB for improved heat dissipation
Exposed solder-able ground pad below the driver IC on the bottom of the PCB
Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor's rated voltage to achieve higher step rates
45 V maximum supply voltage
Built-in regulator (no external logic voltage supply needed)
Module size, pinout, and interface match those of our A4988 stepper motor driver The max running currency: 2.5A
Size: 1.5mmX2mm
Package includes:
1x CNC Shield Board
1x Arduino UNO R3 Board
4x DRV8825 Stepper Motor Driver
4x Aluminum Heatsink
7. Witbot CNC Shield Expansion Board with A4988 Stepper Motor Driver with Heat Sink for Arduino V3 Engraver
Feature
Latest CNC Shield Version 3.0 for ArduinoGRBL 0.9 compatible (Open source firmware that runs on an UNO for Arduino that turns G-code commands into stepper signals)
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
A4988 Stepper Motor Driver Board is a breakout board for Allegro's A4988 DMOS Micro stepping Driver with Translator and Overcurrent Protection; please read the A4988 datasheet carefully before using this product
Description
Specifications:CNC Shield Board:
1>PWM Spindle and direction pins
2>2 x End stops for each axis (6 in total)
3>Coolant enable
4>Uses removable A4988 or DRV8825 compatible stepper drivers
5>Compact design
6>Stepper Motors can be connected with 4 pin molex connectors or soldered in place
7>Runs on 12-36V DC. (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
8>Please note that this is an unassembled kit and Basic soldering skills are needed
A4988 Stepper Motor Driver:
1>Low RDS (On) Output
2>Automatic current decay mode detection / selection
3>Mix with slow current decay modes
4>Synchronous rectification for low power dissipation
5>Internal UVLO
6>Crossover-current protection
7>3.3 and 5 V compatible logic supply
8>Thermal shutdown circuitry
9>Ground fault protection
10>Load short-circuit protection
11>Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16
12>Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it is powered is asking for trouble)
Package Included:
1 x CNC Shield Board
4 x A4988 Stepper Motor Driver
4 x Mini Heat Sink
8. KEYESTUDIO UNO R3 CNC Kit/CNC Shield V3.0 +4pcs A4988 Stepper Motor Driver + UNO R3 ATmega328P with Usb Cable for Arduino GRBL Compatible
Feature
Uno R3 Board for Arduino: USB-TTL used ATMEGA 16U2 chip, controller used ATMEGA 328P chipUS ATMEL original, fast transfer and more memory:), the same circuit arrangement and work as originalLatest Arduino CNC Shield Version 3.0: grbl compatible (open source firmware that runs on an arduino uno that turns G-code commands into stepper signals) 4-Axis support; jumpers to set the micro-stepping for the stepper drivers; runs on 12-36V DC
A4988 Stepper Motor Driver: simple step and direction control interface; thermal shutdown circuit/cross current/ground fault/short circuit protection, five step modes; voltage: 3.3v and 5v; mix with slow current attenuation model etc
FCC and CE certification: this high quality arduino cnc kit is well packaged, solder is very clean, everything is aligned nicely, has made function,voltage, current testing before packaging
It is really safe and great choose for engraver 3d printer manufacturer, arduino learner and diy machine lover
Description
Specification:(1)3D Printer CNC Shield Board V3.0
GRBL compatible.
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
2 x End stops for each axis (6 in total) Spindle enable and direction Coolant enable
Uses removable Pololu A4988 compatible stepper drivers. (A4988, DRV8825 and others)
Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
(2)A4988 Stepper Motor Driver
Thermal shutdown circuitry:Yes
Crossover-current protection:Yes
Ground fault protection:Yes
Load short-circuit protection:Yes
Compatible logic supply: 3.3V and 5 V
Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16
Features:
1.Mix with slow current decay modes.
2.Internal UVLO and Low RDS (On) Output.
3.Automatic current decay mode detection/selection.
4.Synchronous rectification for low power dissipation.
Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver)
(3)Uno r3 Board For Arduino(more details please search the asin B0168B39N4)
Package Included:
1 x Arduino R3 Development Board
1 x Engraver CNC Shield Board
4 x A4988 Stepper Motor Driver
1 x 30 cm USB Cable
9. SainSmart CNC Shield V4 + Nano V3.0 + 3 xA4988 Reprap Stepper Drivers Kit for Arduino 3D Printing
Feature
Compatible with micro-drive laser engraving machine and 3-axis CNC engraving machineCH340 Nano 3.0 controller is an open souced, small and complete board based on the ATmega328.
Complete set of electronics to run small CNC mill, router, lathe or robot
Description
Description:CNC Shield V4.0 features:
- 3 axis stepper motor driver
- Compatible with micro-drive laser engraving machine, three-axis CNC engraving machine.
- 2A can be controlled within the two-phase four-wire stepper motor.
- Released the digital IO interface, easy to connect to other modules, such as ENDSTOP.
- Released the I2C interface, you can connect to the LCD I2C or other I2C module.
- power DC5v interface, 7.5-12V voltage input.
- GRBL compatible
- worked with arduino nano.
CH340 Nano board
CH340 Nano 3.0 controller is a small, complete board based on the ATmega328.
It's a open source Simple I/O platform with 12 Digital I/O Pins (of which 6 provide PWM output), 8 Analog Input Pins, pin 0 (RX) and 1 (TX) used to receive (RX) and transmit (TX) TTL serial data, a Mini-B USB connection, an ICSP header and a reset button.
A4988 stepper driver
This product is a carrier board or breakout board for Allegro's A4988 DMOS Microstepping Driver with Translator and Overcurrent Protection by Pololu; we therefore recommend careful reading of the A4988 datasheet before using this product. This stepper motor driver lets you control one bipolar stepper motor at up to 2 A output current per coil.
Package List:
- 1x CNC Shield V4.0
- 1x nano board
- 3x A4988 driver
- 1x USB cable
10. KINGPRINT CNC Shield V3.0 Expansion Board for Arduino with 4pcs A4988 Stepper Motor Driver with Heatsink Kits for Arduino
Feature
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13), 2 x End stops for each axis (6 in total)Latest Arduino CNC Shield Version 3.0, GRBL 0.9 compatible
Uses removable A4988 or DRV8825 compatible stepper drivers
Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection
Runs on 12-36V DC.
Description
CNC Shield Board:> Open source firmware that runs on an UNO for Arduino that turns G-code commands into stepper signals
> Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping)
A4988 Stepper Motor Driver:
> Automatic current decay mode detection / selection.
> Internal UVLO.
> Mixed with slow current decay modes.
> Synchronous rectification for low power dissipation.
> Crossover-current protection.
> Thermal shutdown circuitry.
> 3.3 and 5 V compatible logic supply.
> Thermal shutdown circuitry.
> Ground Fault Circuit.
> Load short-circuit protection.
> Of five optional step mode: full, 1/2, 1/4, 1/8 and 1/16.
NOTICE:
> powered can destroy the driver. (More generally, rewiring anything while it is powered is asking for trouble
> Please note that this is an unassembled kit and Basic soldering skills are needed
> At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board
Package Contents:
1 x CNC Shield Board
4 x A4988 Stepper Motor Driver(Green)
4 x Heat Sink Notice:
There is no jumper.
